admin管理员组文章数量:1636900
昨天16M闪和USB模块存到了。16M闪存已经请店家用编程器刷上了华硕N14U的编程器固件。路由焊上闪存后出现的问题是进不了192.168.1.1页面,指定网关为192.168.1.1可以进去了,显示是固件恢复页面,在这里刷入华硕的固件,显示成功并且路由自动重启,但是还是和前面一样(进不了192.168.1.1页面,指定网关为192.168.1.1可以进去了,显示是固件恢复页面)。TTL显示
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)
SoC:MediaTek MT7620
DRAM: Memory Testing.65536K OK. is 64 MB
relocate_code Pointer at: 83fac000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
______________________________________________________
| ____ ____ |
| | _ \ _ __ ___ __ _ _ __ ___ | __ ) _____ __ |
| | | | | '__/ _ \/ _` | '_ ` _ \| _ \ / _ \ \/ / |
| | |_| | | | __/ (_| | | | | | | |_) | (_) >
| |____/|_| \___|\__,_|_| |_| |_|____/ \___/_/\_\ |
| |
| DreamBox Team |
| http://www.openwrt |
| Board:Mercury MW305R |
| |
| lintel |
|____________________________________________________|
===============System Info==================
ASIC 7620_MP (Port5None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:64 Mbytes
Build Date:Jan 29 2013 Time:15:41:44
============================================
GPIO Init:
UARTF_SHARE_MODE:GPIO
I2C_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name:
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 12970108 Bytes = 12.4 MB
Load Address: 80000000
Entry Point: 8000c150
raspi_read: from:50040 len:c5e87c
版权声明:本文标题:fwr310刷openwrt_全网首拆迅捷FWR310 V4.0 300M 路由硬改后刷华硕N14U 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://www.elefans.com/xitong/1729237653a1192074.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论