admin管理员组文章数量:1565357
2024年7月11日发(作者:)
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:1/15
Specification of Li-ion Rechargeable Battery
锂离子电池规格书
Prepared by
肖志军
Checked by
Approved by
Model:602030PL300mAh/3.7V
Customer Name:
Customer No.:
Comment:
Customer
Confirmation
Customer Approval:
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:2/15
兴永恒(深圳)电子有限公司
深圳宝安区沙井后亭
E-mail:****************
Website:
TEL:86-
FAX:86-
AMENDMENT RECORDS
REVISION DATE ORIGINATOR REASON FOR REVISION
A001
2016-6-20
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:3/15
Content目录
1. Scope范围 .................................................................................................................................................... 4
2. Reference Standard 参考标准 ...................................................................................................................... 4
3. Picture of battery电池图 .............................................................................................................................. 4
3.1 Picture of single cell 单体电芯图 ........................................................................................................... 4
3.2 Picture of assembled battery 组合电池图 .............................................................................................. 6
4. Basic of performance 基本性能 ................................................................................................................. 7
4.1 Single cell parameters 单体电芯参数 .................................................................................................... 7
4.2 Assembled cell parameters包装后电芯组参数 ...................................................................................... 8
5. Electrical Characteristics电性能 .................................................................................................................. 8
5.1 Normal Test Conditions标准测试条件 .................................................................................................. 8
5.2 Electrochemical Characteristics电化学性能 .......................................................................................... 8
5.3 Environment Characteristics环境适应性能 ........................................................................................... 9
5.4 Safety Characteristics 安全性能 ........................................................................................................... 10
6. PCM Specification PCM 规格 ................................................................................................................. 11
6.1 Electrical Characteristics电性能 ............................................................................................................ 11
6.2 Circuit Diagram 电路图 ......................................................................................................................... 11
6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明 ........................................... 12
6.4 PCM BOM 保护板物料清单 ............................................................................................................... 12
7. Storage and Shipment Requirement存储及运输要求 ............................................................................... 13
8. Warning and Cautions 警告及注意事项 .................................................................................................... 13
9. Note 声明 ................................................................................................................................................... 15
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:4/15
1.
Scope范围
This specification describes the performance, testing method, warning and caution of the lithium-ion
rechargeable battery.
The specification applies to polymer battery supplied by Shenzhen biyate energy co., ltd
本标准描述了锂离子电池的性能、测试方法及注意事项。
本标准适用于东莞市高超新能源有限公司生产的聚合物锂离子电池
2. Reference Standard 参考标准
The standard refer to GB/T18287-2000, UL1642 and the other technology standard.
本标准参考国标GB/T18287-2000、UL1642等技术标准规范编制而成。
3. Picture of battery电池图
3.1 Picture of single cell 单体电芯图
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:5/15
厚度T
6.0±0.3
宽度W
20±0.5
长度L
30±0.5
UNIT单位:MM
L1
8
W1
2.0
E
15±3
Fig. (1) The Dimension of Single Cell
图(1) 单体电池尺寸图
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:6/15
3.2 Picture of assembled battery 组合电池图
L2
L1
+DATE
3.7V 300mAh
- GC
602030
L
厚度T
6.0±0.3
宽度W
20±0.5
长度L
30±2
L1
30±5
线径Ø
0.8
L2
0
插头型号
无
UNIT单位:MM
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:7/15
Fig. (2) The Dimension of Assembled Battery
图 (2) 组合电池外形尺寸图
4. Basic of performance 基本性能
4.1 Single cell parameters 单体电芯参数
No.
1
2
3
4
5
6
Item项目
Rated Capacity
额定容量
Minimum Capacity
最小容量
Normal Voltage
标称电压
O.C.V 出厂电压
Charge Ending Voltage
充电截止电压
Discharge Ending Voltage
放电截止电压
Standard charging method
标准充电方式
Charge current
充电电流
charging Time
充电时间
Max. Charging Current
最大充电电流
Specification性能
300mAh ,0.2 C discharging
300mAh ,0.2 C discharging
3.70V
3.80-4.2V
4.20±0.03V
2.75V
0℃~45℃ 0.5C constant current charge to 4.2V, then
constant voltage 4.2V charge till charged current
declines to ≤ 0.01C
Standard charge:0.2C
Rapid charge:1.0C
Standard charge:5.5~6.5 h
Rapid charge:1.5~2.5 h
1.0C (5℃~+45℃)
7
8
9
10
11
12
13
Standard discharging
-20℃~+60℃ 0.2C constant current discharge to 3.0V.
Current标准放电电流
Max. Discharging Current
最大放电电流
Operating environment
工作环境
1.0C (-20℃~+60℃)
Charging: 0℃-45℃, 65%±25%RH
Discharging: -20℃-60℃, 65%±25%RH
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:8/15
14
Cell Impedance
单电芯内阻
Dimension of Single Cell
单电芯尺寸
<100mohm,(4.2V AC 1KHz measured)
Thickness Max 3.0mm
Max 20mm
Max 30mm
15
Width
Height
4.2 Assembled cell parameters包装后电芯组参数
序号
1
2
3
4
Item项目
Assembled Mode
组合方式
Normal Capacity
标称容量
Normal Voltage
标称电压
Impedance
成品内阻
Assembly Dimension
装配尺寸
Specification性能
1P
≥300mAh, 0.2 C discharging
3.7V
<160mohm,(100% charge AC 1KHz measured)
Thickness Max6.3mm
Max20.5mm
Max30.0mm
5
Width
Height
5. Electrical Characteristics电性能
5.1 Normal Test Conditions标准测试条件
Temperature: 15~35℃
Relative Humidity: 45-85%RH
Atmospheric pressure: 86 -106 KPa
除非另有规定,本规格书中的各项测试应在标准大气条件下进行:
温度: 15~35 ℃
相对湿度:45-85%RH
大气压力:86 ~106 KPa
5.2 Electrochemical Characteristics电化学性能
NO.
序号
Item
项目
Criterion
性能标准
Test Method
测试方法
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:9/15
Discharging After Standard Charging, rest 5 minutes ,then
capacity is not 0.2C discharge to ending voltage
less than normal
标准充电后,
电芯放置5分钟,再0.2C放电至
capacity.
终止电压。
放电容量应不
小于标称容量
2 1C Discharging After Standard Charging, rest 5 minutes ,then 1C
discharging capacity is not discharge to ending voltage
capacity less than 90%
标准充电后,电芯放置5分钟,再1C放电至
1C放电性normal capacity.
终止电压。
能 放电容量应不
小于标称容量
的90%
3 Cycle life The cycle times Test condition:
循环寿命
is not less than Charge:0.5C to4.2V
300 Discharge:0.5C to 3.0V
循环次数不小
When the discharge capacity reduced to 80% of
于300次
rated capacity, Stop testing
测试条件:
充电:0.5C充电到4.2V
放电:0.5C放电到3.0V
当放电容量降至额定容量的80%时,停止测试。
4 Self- Discharging After Standard Charging, test condition:
dischargecapacity is not Temperature:20±5℃
自放电
less than 90% Storage Time:28days
initial capacity Then 0.2C discharge to ending voltage
放电容量应不标准充电后,测试条件如下:
低于初始容量温度:20±5℃
的90% 搁置时间:28天
再以0.2C放电至终止电压。
5.3 Environment Characteristics环境适应性能
1 0.2C
discharging
capacity
0.2C 放电
性能
NO
序号
1
Item
项目
Constant
temperature
and
constant
humidity
test
Criterion
性能标准
No explosion,no
fire, no leakage.
Discharging
capacity is not
less than 85%
initial capacity
Test Method
测试方法
After Standard Charging, test condition:
Temperature:40±5℃
Relative Humidity:90~95%RH
Storage Time:96 hours
Then return to room temperature for 2 hours,
Then 1C discharged to ending voltage
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:10/15
恒定湿热 不起火、不爆
炸、不泄漏。
放电容量不低
于初始容量的
85%
No explosion, no
fire,no leakage
不起火、不爆
炸、不泄漏。
2 Vibration
test
振动
3 Shock test
碰撞
No explosion, no
fire,no leakage
不起火、不爆
炸,不泄漏。
标准充电后,测试条件如下:
温度:40±5℃
相对湿度:90~95%
放置时间:96小时
电芯取出在室温下放置2小时,然后以1C电
流放电至终止电压。
After Standard Charging,fixed the cell to
vibration table, then subjected to vibration test
for 30 minutes per axis of XYZ axes
Frequency rate:1oct/min
Vibration frequency:10Hz-55Hz
Excursion (single amplitude):0.8mm
电芯按标准充电后,固定在振动台上,然后沿
XYZ每个坐标方向振动30分钟
扫频速率:1oct/min
振动频率:10Hz~55Hz
位移幅值(单振幅):0.8mm
After Standard Charging,test condition:
Acceleration:100m/s
2
Pulse lasting time:<16ms
Shock times:1000±10 times
标准充电后,测试条件如下:
加速度:100m/s
2
脉冲持续时间:<16ms
碰撞次数:1000±10
5.4 Safety Characteristics 安全性能
NO Item
序号 项目
1
Criterion
性能指标
Test Method
测试方法
Discharge : 1C to3.0V
Charge : 1C charge to 4.8V, and maintain 8
h
放电:1C放电至3.0V
充电:1C充电4.8V,保持8小时
After Standard Charging,Short circuit the
positive and negative,and the resistance of
copper wire is not more than 100mΩ 。
标准充电后,使用总内阻不大于100mΩ
的导线短路正负极。
Overcharge No explosion, no fire
test
不起火、不爆炸
过充电性
能
Short
circuit
test
短路
No explosion, no fire,
The temperature of the
surface of the Cells are
lower than 150℃
不起火、不爆炸,电芯
2
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:11/15
表面温度不超过
150℃。
3
4
Forced
discharge
过放试验
Free
fall test
自由跌落
No explosion, no fire
不起火、不爆炸
No Leakage ,no
explosion,no fire 。
不漏液,不爆炸,不起
火。
Discharge at a current of 1 C5A for 2.5h.
以1CmA 的电流放电2.5小时
The battery to be fully charged with
standard charging condition ,then fall from
height of 1.0m and hit onto concrete
ground 2 times
电池标准充电后,让其从1.0m高处自由
落下,跌落在混凝土地面上2次。
Note: Above testing of safe characteristics must be with protective equipment.
备注:以上安全性能实验应在有保护措施的条件下进行。
6. PCM Specification PCM 规格
6.1 Electrical Characteristics电性能
(Normal temperature, Relative humidity≤90%) (室温, 湿度≤90%)
NO.序号
1
2
3
4
5
Item项目
Over-charging Protection
过充保护电压
Over-discharging Protection
过放保护电压
Discharge Current Protection
过流保护电流
Internal Resistance
正常工作时导通内阻
Operation Static Current
工作状态消耗电流
Specifications规格
4.28±0.05V
2.40±0.10V
2.0~6.0A
R≤65mΩ
≤6.0uA
6.2 Circuit Diagram 电路图
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:12/15
6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明
6.4 PCM BOM 保护板物料清单
序
号
1
2
3
4
5
6
物料代
码
U1
U2
R1
R2
C1
PCB
物料名称
控 制 IC
MOS 管
贴片电阻
贴片电阻
贴片电容
线 路 板
规格型号
DW01A
8205A
100Ω±5% 1/16W 0402
1K 1/16W 0402
0.1uF±10% 16V 0402
15*3.8*0.6mm
封装形式
SOT-23-6
SOT-8
0603
0603
0603
数量
1
2
1
1
1
1
备注
富晶
富晶
三星
三星
三星
佰特锐
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:13/15
7. Storage and Shipment Requirement存储及运输要求
Item Requirement
项目 要求
Short period less than 1 month
-20°C ~ +45°C,65%±25%RH
短期少于一个月
Long period less than half year
-20°C ~ + 35°C,65%±25%RH
长期小于半年
Long period less than 1 year
0°C~+30°C,65%±25%RH
长期小于一年
Long time storage :
If the cell is stored for a long time, the cell’s storage voltage should be 3.70-3.95V and
the cell is to be stored in a condition as above requirement. Also, it is recommended to
charge the cell every six months.
of Warranty 保质期
The period of warranty is one a year from the date of shipment. Within the battery idle for at least six months to charge
the battery activation time, because if the idle time is too long and that the battery performance of the company is not
responsible for any damage,
GC
guarantees to give a replacement in case of battery with defects proven due to manufacturing
process instead of the customers abuse and misuse.
电池的保质期从出货之日算起为一年。电池闲置六个月之内至少给电池充电激活一次,如果因为闲置时
间过长而导致电池性能受损本公司概不负责,如果证明电池的缺陷是在我们公司制造过程中造成的而不
是客户滥用或错误使用造成,本公司负责退换电池。
9. Warning and Cautions 警告及注意事项
Danger warning (it should be described in manual or instruction for users, indicated especially) to prevent the
possibility of the battery from leaking, heating, explosion. Please observe the following precautions:
危险警告:(应在使用说明手册或说明书中,特别注明)为防止电池可能发生泄漏,发热,爆炸,请注
意以下预防措施:
Don’t immerse the battery in water and seawater. Please put it in cool and dry environment if no using.
严禁将电池浸入海水或水中,保存不用时,应放置在阴凉干燥的环境中。
Do not discard or leave the battery near a heat source as fire or heater
禁止将电池在热高温源(如火、加热器)旁等使用、留置或丢入。
Being charged, using the battery charger specifically for that purpose
充电时请选用锂离子电池专用充电器。
Don’t reverse the positive and negative terminals
严禁颠倒正负极使用电池。
Don’t connect the battery to an electrical outlet directly.
严禁将电池直接接入电源插座。
Don’t connect the positive and negative terminal directly with metal objects such as wire. Short terminals of
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:14/15
battery is strictly prohibited, it may damage battery.
禁止用金属直接连接电池正负极短路,任何时候禁止短路电芯,它会导致电芯严重损坏。
Do not transport and store the battery together with metal objects such as necklaces, hairpins.
禁止将电池与金属,如发夹,项链等一起运输或贮存。
Do not strike , throw or trample the battery.
禁止敲击或抛掷,踩踏电池等。
Do not directly solder the battery and pierce the battery with a nail or other sharp object
禁止直接焊接电池和用钉子或其它利器刺穿电池。
Do not use lithium ion battery and others different lithium polymer battery model in mixture
禁止与液态锂离子或不同型号的聚合物锂电池混合使用
Prohibition of use of damaged cells
禁止使用已损坏的电芯
Don’t bend or fold sealing edge. Don’t open or deform folding edge Don’t fillet the end of the folding edge
禁止弯折顶封边,禁止打开或破坏折边,禁止导折电芯折边底部
Don’t fall, hit, bend battery body.
禁止坠落、冲击、弯折电芯。
Battery pack designing and packing Prohibition injury batteries.
电池外壳设计和包装禁止损伤电池。
Never disassemble the cells
在任何情况下不得拆卸电芯
The battery replacement shall be done only by either cells supplier or device supplier and never be done by the
user.
更换电芯应由电芯供应商或设备供应商完成,用户不得自行更换。
Keep the battery away from babies.
电池应远离小孩.
Caution小心
◆ Do not use or leave the battery at very high temperature conditions (for example, strong direct sunlight or
a vehicle in extremely hot conditions). Otherwise, it can overheat or fire or its performance will be degenerate
and its service life will be decreased.
禁止在高温下(直热的阳光下或很热的汽车中)使用或放置电池,否则可能会引起电池过热,起火或功
能失效,寿命减短。
◆ Do not use it in a location where is electrostatic and magnetic greatly, otherwise, the safety devices may be
damaged, causing hidden trouble of safety.
禁止在强静电和强磁场的地方使用,否则易破坏电池安全保护装置,带来不安全的隐患。
◆ If the battery leaks, and the electrolyte get into the eyes. Do not wipe eyes, instead, rinse the eyes with
clean running water, and immediately seek medical attention. Otherwise, eyes injury can result.
如果电池发生泄漏,电解液进入眼睛,请不要揉擦,应用清水冲洗眼睛,并立即送医治疗,否则会伤害
眼睛。
◆ If the battery gives off an odor, generates heat, becomes discolored or deformed, or in any way appear
abnormal during use, recharging or storage, immediately remove it from the device or battery charge and stop
锂离子聚合物电池规格书
Specification of Li-ion Polymer Battery
602030PL300mAh
编 号:XYH-602030-1
版 本:A001
页 码:15/15
using it.
如果电池发出异味,发热,变色,变形或使用,贮存,充电过程中出现任何异常现象,立即将电池从装
置或充电器中移离并停用。
◆ In case the battery terminals are dirt, clean the terminals with a dry cloth before use. Otherwise power
failure or charge failure may occur due to the poor connection with the instrument.
如果电池弄脏,使用前应用干布抹净,否则可能会导致接触不良功能失效。
Prohibition of use of damaged cells
禁止使用已损坏的电芯
◆ Be aware discharged batteries may cause fire; tape the terminals to insulate them.
废弃之电池应用绝缘纸包住电极,以防起火,爆炸。
10. Note 声明
Note (1): The customer is requested to contact in advance if and when the
variations of the operating conditions described in this document. Additional
experimentation may be required to verify performance and safety under such conditions.
声明一:
客户若需要将电芯用于超出文件以外的设备,或在文件规定以外的使用条件下使用电芯,应
事先联系。因为需要进行特定的实验测试以核实电芯在该使用条件下的性能及安全性。
Note (2): take no responsibility for any accident when the cell is used under
conditions outside of this specification.
声明二:
对于在超出文件规定以外的条件下使用电芯而造成的任何意外事故, 概不负责。
Note (3): inform the customer in writing of improvement(s) regarding proper use
and handling of the cell if it is deemed necessary.
Energy reserves the right to revise this specification before the customer signs the
datasheet. If a revision is required, notify the customer.
声明三:
如有必要会以书面形式告知客户有关正确操作使用电芯的改进措施。
在规格书未签确前,本公司有权对本产品规格书进行修订,如有必要修订后将会通
知客户。
Appendix.附录
N/A
版权声明:本文标题:锂离子聚合物电池规格书说明书 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://www.elefans.com/xitong/1720691005a837961.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论