admin管理员组文章数量:1630616
2024年1月6日发(作者:)
常用电器英语对照翻译
Major Appliance
flashlight 手电筒
fluorescent lamp 日光灯
electric calculator 计算器
tube 真空管
electric fan 电风扇
dictaphone, dictating machine 录音机
magnetic tape 磁带
television 电视机
electric iron 电熨斗
electric foot warmer 暖脚器
electric shaver 电动剃须刀
electric cooker 电饭锅
electric heater 电暖气
electric vacuum cleaner 吸尘器
bulb 电灯泡
electric oven 电烤箱
radio 收音机
microphone 麦克风
loud-speaker 扩音机
refrigerator 冰箱
air conditioner 空调
microwave oven 微波炉
dry cell 干电池
tap 电线搭接处
MISSING „„„„„. 缺少„„„„„ , 掉了„„„„„.
例句:
--- MISSING COMPONENTS 缺另件
--- MISSING PARTS 缺零件
--- MISSING MANUAL 缺操作说明
--- MISSING INSTRUCTION LEAFLET 缺说明书
--- MISSING BROCHURE 缺简介小册
--- MISSING LABEL 缺标签
--- MISSING STICKER 缺贴纸
--- MISSING BAR CODE 缺条形码
--- MISSING ASSEMBLE SHEET 缺组装说明
--- MISSING 3/16” SLOTTED BIT 缺3/16” 一字起子头
--- MISSING 10 MM DEEP SOCKET 缺10 MM 长套筒
2. N. ( V + ING ) OF„„. PARTS ( 或 ON „„„ SURFACE )
例句:
--- PITTING OF METAL PARTS 金属零件凹陷
--- FLAKING OF CHROME PLATING 镀铬层剥脱壳
--- FLASHING OF PLASTIC PARTS 塑料零件毛边
--- FAILURE ON COATING SURFACE 烤漆表面不合格
--- DEFORMATION OF RACK 框架变形
--- MOULDING OF WOODEN HANDLE 木柄发霉
--- CHIPPING ON STEEL PIPE SURFACE 铁管表面裂伤
--- CRACKING OF 13 MM SOCKET 13 MM 套筒裂痕
--- DENT ON METAL PLATE SURFACE 金属板表面凹痕
--- NICK OF PLASTIC CASE 塑料盒割痕
--- DUST OF PACKAGE 包装尘污
--- RUSTING ON PLATING SURFACE 电镀表面生锈
--- SMUTTING OF ARTWORK 彩卡脏污
--- SCRATCHING ON COATING SURFACE 烤漆表面刮伤
--- SHARP EDGE OF HANDLE 手柄锐边
--- CORROSION ON METAL SURFACE 金属表面腐蚀
--- PEELING OF CHROME PLATING 镀铬层剥落
--- BURRS OF GRINDING EDGE 研磨端毛边
3. POOR + N. ( V + ING ) OF „„„ 不良的„„. , 太差的 „„.
例句:
--- POOR MARKING OF LOGO 商标印字不良
--- POOR LABELING OF STICKER 贴纸黏贴不良
--- POOR COATING OF FRAME 支架烤漆不良
--- POOR MOLDING OF PLASTIC HANDLE 塑料手柄成型不良
--- POOR RIVETING OF PLATE CONNECTION 平板铆接不良
--- POOR FORMING OF SHELF 棚架成型不良
--- POOR PLATING 电镀不良
--- POOR CLEANING 清洁不良
--- POOR PRINTING 印刷不良
--- POOR GLUING 胶合不良
--- POOR ASSEMBLING组装不良
--- POOR JOINT 接合不良
--- POOR BALANCE 平衡不良
--- POOR LASER MARK雷射不良
--- POOR SHAVING 车削不良
--- POOR EMBOSSING 滚花不良
--- POOR PACKAGING 包装不良
4. …… NOT MEAT…… , …… OUTSIDE ……. ,
„„ NOT MATCH „„. „„..不符合„„..
例句:
--- CONTENTS NOT MATCH P/O内容物不符订单
--- OVERALL LENGTH NOT MEAT SPEC总长度不符规格
--- HARDNESS OUTSIDE STANDARD硬度不符标准
--- PRODUCTS NOT MATCH SEALED SAMPLE产品不符确认样品
--- PACKAGE NOT MEAT P/O包装不符订单
--- FUNCTION NOT MEAT REQUIREMENT 功能不符需求
5. „„„ FAILED , „„„. 不合格
例句:
--- IMPACT TEST FAILED 冲击测试不合格
--- GO / NO GO GAGE FAILED 塞规测试不合格
--- TORQUE TEST FAILED 扭力测试不合格
--- HARDNESS TEST FAILED 硬度测试不合格
--- DROP TEST FAILED 落地测试不合格
--- PERMNENT TEST FAILED 变形测试不合格
--- WIRE CUTTING TEST FAILED 剪钢线测试不合格
--- BENDING TEST FAILED 弯折测试不合格
--- STRENGTH TEST FAILED 张力测试不合格
--- STRIKING TEST FAILED 敲击测试不合格
Burr 毛边,飞边
Shinking 缩收
Sharp edge 尖锐边
color deviation 色差
cut by worker without
approval 未经同意切削
material mark 材料痕
shining abnormal 异常发亮
fail frozen testing/missle test 冷冻/导弹测试失败
injection defect, not functional problem--注不满
injection defect, functional problem--注不满, 影响功能
white mark 白痕, 发白
joint finger 指接
wood texture incorrect 木头纹理不正确
Moisture outside the scope (8~14 degree) 湿度不满足要求
Worm hole 虫孔
Decayed parts 腐烂
Waney component
Water stains
warp (the max deformation is less than 1/8 inch) 翘曲,小于1/8“
warp (the max deformation is more than 1/8 inch) 翘曲,大于1/8“
Mineral streak line 矿物纹
Fast/dead knot
死结
Live knot 活结
Chip---doesn't cause sharp point 碎片不引起尖锐点
Chip---does cause sharp point 碎片引起尖锐点
Crack ---affect safety concern 裂缝影响功能
Crack---lobed crack (表裂)
Split
开裂
Dent ---doesn't expose on visible position or depth
less than 1 mm 弯曲,不可视或小于1mm
Dent --- expose on visible position or depth more
than 1 mm
弯曲,可视或大于1mm
Indentation
凹痕
Gluing position with gap 胶粘,有缝隙
Gluing line is obvisible 胶粘线可视
incorrect texture
纹理不正确
string broken or emersion
断线或脱线
slight color deviation
轻微色差
serious color deviation 严重色差
softgoods fail test, 色牢度,抗撕,抗拉,耐磨性 测试失败
thickness doesn't meet request
密度不满足要求
pin left in softgoods
断针
shrinkage
缩水
deformed
变形
flash/gate remnant
matted
无光泽
flow line/stress mark
夹水纹/顶白
poor molding
喷塑不良
contamination mark
混色,混料
mark 痕迹,污点,标记
colourized 混色
color deviation 颜色偏差
color mismatched 颜色不配合
burnt mark 烧焦痕
damaged 烂/损坏
poor trimming 修整不良
dull surface 哑色
poor spraying 喷油不良
over spraying 飞油
paint under coverage油太薄
paint chipped off脱油
orange peel painting油面呈橙皮壮
foreign painting染油
poor re-painting touchup补油不良
missing spraying漏喷油
dirty on paint surface油面有尘点
paint bubbles油泡
paint color deviation油颜色偏差
paint color mismatched喷油颜色不配合
paint abrasion fail油漆被擦
paint adhesion fail油漆被甩
paint dirty油面污糟
spraying scratched喷油刮花
dull of paint surface
喷油哑色
paint matted/frayed
喷油无光泽/磨损
yellowish painting
油面发黄
paint peel off
油面起皮
spraying uneven
喷油不整齐
paint damped
油漆不干
paint abrasion
甩油
bubble
冒泡,气泡
uneven paint coverage
喷油厚薄,不均
paint misregistration
错色
poor coating
油漆外层不良
Incorrect material using cause the structure or safety concern 材料不正确 引起结构或功能性缺陷
2Same element material using
but the character is different
元素相同但是特性不同
3powder coating don't pass heavy metal content test by 3rd lab 粉末未能通过第三方重金属测试
4
5
1Hardness don't meet request 硬度不满足要求
2Tensile don't meet request
抗拉测试不通过
3.1thickness don't meet drawings request, slightly deviation, the product can pass testing.
厚度不满足图纸要求, 有轻微偏差但不影响成品测试
3.2thickness don't meet drawings request,the product can't pass testing.
厚度不满足图纸要求, 成品测试失败
3.3for Europe ALU. Parts, the thickness less than 1.2mm 销欧洲产品,铝部件厚度小于1.2mm
4Alu material analysis don't meet GB standard 铝材质分析不满足国标
5Alu parts don't well packaged during transportation.内部转运过程未有效保护铝部件
6the parameters didn't meet SOP during Alu process monitor 铝制造过程控制参数不满足SOP要求
1Barcol Hardness don't meet request, less than 50 minimum 巴氏硬度不满足要求, 小于50 度
2use the wrong roving and felt and glass fiber during extrusion 挤压工序材料用错,粗纱,毡制品,玻璃纤维
3wall thickness(including other dimensions) don't match requirement 壁厚不满足要求
4color deviation, not uniform
部件色差,
5
Missing components 包裝零件丟失
2Incorrect packing method 包裝方式錯誤
3.1Light deforming of packing but don’t damage the products 輕微包裝變形但不會造成產品損傷
3.2Serious deforming of packing but don’t damage the products 嚴重包裝變形但不會造成產品損傷
3.3Serious deforming or damage of packing but don't damage the product 嚴重包裝變形或损坏且不造成產品損傷
3.4Serious deforming or damage of packing and damage the product 嚴重包裝變形或损坏且造成產品損傷
4.1Seam missing 紙箱未封口
4.2Poor taping / gluing and the opening on the cover panel 封箱不良, 箱蓋開口
5Miss UPC 條碼標未貼
6Miss Sticker or warning 要求之貼紙或警告標語未貼
7.1Container loading - No container inspection 没执行货柜检查
7.2Container loading - Dirt of Conatiner 货柜脏
7.3Container loading - Incorrect loading way 装柜方式不正确
8metal scissor/ knife pieces leave in box.
刀具
Master Carton / Color Box1Incorrect structure 紙箱結構不符要求
2.1Incorrect seam method but no problem to pack the products and pass the test requirements of
QR 紙箱和縫方式不正確但不影響包裝且通過QR測試
2.2Incorrect seam method and the goods can not be well packed. 紙箱和縫方式不正確且影響包裝
3.1Poor seam with the opening 紙箱和縫處不良並有開口
3.2Poor seam with the opening and safety concern 紙箱和縫處不良並且有安全考量
4.1Incorrect dimension but no problem to pack the products and pass the test requirements of QR
紙箱尺寸不正確但不影響包裝且通過QR測試
4.2Incorrect dimension and the goods can not be well packed 尺寸不正确影响包装质量
5Incorrect shipping mark 麥頭錯誤
6.1Un-clear shipping mark but no problem to read 輕微印刷不清楚, 但仍可辨識
6.2Un-clear shipping mark and can not read 印刷不清楚, 且無法辨識
7Incorrect Graphic printing 圖案印刷錯誤
8.1Serious tearing - less than 2cm length 嚴重撕裂小于2cm 長度
8.2Serious tearing - 2~5cm length 嚴重撕裂2~5cm 長度
8.3Serious tearing - over 5cm length or tearing two areas 嚴重撕裂超過5cm 長度或两处以上
9.1Broken less than 2cm 破裂小于2cm 長度
9.2Broken -- 2~5 cm length
破裂2~5 cm 長度
9.3Broken over 5cm, product visible 破裂超過5cm 長度
10.1Visual dirt mark, spot, water mark etc„ between 5 to 10 square cm and less than area 髒污點介於5 至10 平方cm
10.2Visual dirt mark, spot, water mark etc… over 10 square cm
髒污點大於10 平方cm
11UPC can not be read 條碼無法讀取
surface roughness don't meet requirement 表面粗糙度不满足要求
6material or parts have particles, foreign materials, pits, cracks, voids, chips, sink marks,
delaminations, blisters or scratches.
材料、部件有粒子,杂质,凹陷,开裂,中空,碎片,缩痕、分层、水泡或划伤
7material has resin-rich, resin- starved areas, significant shifting, wrinkles, bunching up, density
variation 树脂分布区域不平衡,明显变化,皱纹,聚成团,密度变化等现象
8material failed electrical, thermal, structural, outdoor weather-resistant characteristics. 材质不符合电、热、结构、室外抗风化等特性
9nonflammability
failure 不可燃性不符合要求
10density out of requriement range 0.065lb/inch3, tolerance +/- 10%.
密度超出要求范围
11failed" water absorption 0.75% maximum" 违反吸水率不得超过0.75%的要求
12fail the DC current leak test 直流漏电测试失败
Standard: shall not exceeed 90 microamperes when 90-kilovolts voltage is applied to electrodes
spaced 10" apart on a length of rail-composite conditioned for 72h at 72 ℉&60 percent relative
hunidity
13fail AC dielectric strength test 交流电绝缘强度测试失败
Standard: A full section of 1" rail material shall have a dielectric strength of at least 25000vt.
14fail flexural modulus requirement, shall be 2.8*1000000 PSI minimum. 饶曲模量不符合要求
1Hardness don't meet request 硬度不满足要求
2twist test failure 扭曲测试失败
3without screw-thread or any defects due to assembly impossible 没有螺纹或其他原因导致无法组立
4spring doesn't pass cyclic test according to drawing
弹簧不能通过疲劳测试
5dimension deviation 尺寸偏差,不影响功能
6fail testing 其他测试失败
1Hardness don't meet request 硬度不满足要求
2thickness don't meet request 厚度不满足要求
3roundness deviation 圆度偏差
4insert doesn't on right position 套管位置偏移
5fail testing--抗弯强度
1.雾气 Moisture Streaks
2.玻纤分配不均 Glass Fiber Streaks
3.困气 Gas Trap Effect
4.银丝纹 Sliver Marks
5.结合线 Weld Line
6.水波痕 Water Wave Effect
7.黑点 Dark Sport
8.顶出印 Visible Ejector Marks
9.变形 Deformation During Demolding
10.填充不足 Short Filling
11.冷料流痕 Cold Slug
12.进胶口点不良 Dull Spots Near The Sprue
13.喷射痕 Jetting
14.表面起层 Flaking Of The Surface Layer
15.浮泡 Entrapped Air
16.过热变色 Burnt Streaks
17.龟裂 Stress Crack
18.缩水痕 Sink Marks
19.真空气泡 Density Bubble
20.披锋 Flash
21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface
22 尺寸过大 Over dimension
23尺寸过小 Under dimension
24 翘曲 Warpage/warped
25 收缩 Shrinkage/shrink
26 缩影 Sink marks
27 打不满 Short shot/short molding
Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子
worktable 工作桌
OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板
barcode条形码 barcode scanner条形码扫描仪 fuse together熔合 fuse machine热熔机 repair修理 operator作业员
QC品管 supervisor 课长 ME制造工程师 MT制造技术 cosmetic inspect外观检查 inner
parts inspect内部检查 thumb screw大头螺丝 镑、英寸 EMI gasket导电条 front plate前板 rear plate后板
chassis |'∫?si| 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of
SPS高源高压测试 Voltage switch of SPS电源电压接柆键 sheet metal parts 冲件 plastic parts塑料件
SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱
sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门
planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机
punching machine 冲床
robot机械手 hydraulic machine油压机 lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting
machine铆合机
position职务 president董事长 general manager总经理 special assistant manager特助 factory
director厂长 department director部长 deputy manager |'depjuti| =vice manager副理 section
supervisor课长
deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line
supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库
pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect
material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to
load material上料 to unload material卸料 to return material/stock to退料 scraped |'skr?pid|报废 scrape ..v.刮;削 manufacture procedure制程 deficient manufacturing procedure制程不良
oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective
to staking铆合不良 embeded lump|in'bed| |l?mp|镶块 feeding is not in place送料不到位
stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal
improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车
compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a
department部门名称 administration/general affairs dept总务部 automatic crewdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective
product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板
stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 pallet栈板
glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol
container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器
rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the
floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机
packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良e = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a
die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to
lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file,
chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound
die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die
plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of
customs count会计师盘,点数量the first page第一联filed by accounting department for
reference会计部存查end-user/using unit(department)使用单位summary of year-end physical
inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory
list will be sent to accounting department together (Those of NHK will be sent to financial
department)本表请与盘点清册一起送会计部-(NHK厂区送财会部)Application status records
of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering
mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming
material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet
物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点difference quantity差异量cause analysis原因分析raw materials原料materials物料
finished product成品semi-finished product半成品packing materials包材good product/accepted
goods/ accepted parts/good parts良品defective product/non-good parts不良品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机
coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒
trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active
plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert
入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬
desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished ducts成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能
poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting
machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色
gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车
mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差
velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed
steel钨高速的
moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类
plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯
CPU: central processing unit(中央处理器)
IC: Integrated circuit(集成电路)
Memory IC: Memory Integrated circuit(记忆集成电路)
RAM: Random Access Memory(随机存取存储器)
DRAM: Dynamic Random Access Memory(动态随机存取存储器)
SRAM: Staic Random Access Memory(静态随机存储器)
ROM: Read-only Memory(只读存储器)
EPROM:Electrical Programmable Read-only Memory
(电可抹只读存诸器)
EEPROM: Electrical Erasbale Programmable Read-only Memory(电可抹可编程只读存储器)
CMOS: Complementary Metal-Oxide-Semiconductor
(互补金属氧化物半导体)
BIOS: Basic Input Output System(基本输入输出系统)
Transistor:电晶体
LED:发光二极体
Resistor:电阻
Variator:可变电阻
Capacitor:电容
Capacitor array:排容
Diode:二极体
Transistor:三极体
Transformer:变压器(ADP)
Oscillator:频率振荡器(0sc)
Crystal:石英振荡器
XTAL/OSC:振荡产生器(X)
Relay:延时器
Sensor:感应器
Bead core:磁珠
Filter:滤波器
Flat Cable:排线
Inductor:电感
Buzzer:蜂鸣器
Socket:插座
Slot:插槽
Fuse:熔断器
Current:电流表
Solder iron:电烙铁
Magnifying glass:放大镜
Caliper:游标卡尺
Driver:螺丝起子
Oven:烤箱
TFT:液晶显示器
Oscilloscope:示波器
Connector:连接器
PCB: printed circuit board(印刷电路板)
PCBA: printed circuit board assembly(电路板成品)
PP:并行接口
HDD:硬盘
FDD:软盘
PSU: power supply unit(电源供应器)
SPEC:规格
Attach:附件
Case: 机箱,盖子
Cover:上盖
Base:下盖
Bezel:面板(panel)
Bracket:支架,铁片
Label :贴纸
Guide:手册
Manual:手册,指南
Card:网卡
Switch:交换机
Hub:集线器
Router:路由器
Sample:样品
Gap:间隙
Sponge:海绵
Pallet:栈板
Foam:保利龙
Fiber:光纤
Disk:磁盘片
PROG:程序
Barcode:条码
System:系统
System Barcode:系统条码
M/B: mother board:主板
CD-ROM:光驱
FAN:风扇
Cable:线材
Audio:音效
K/B: Keyboard(键盘)
Mouse:鼠标
Riser card:转接卡
Card reader:读卡器
Screw:螺丝
Thermal pad:散热垫
Heat sink:散热片
Rubber:橡胶垫
Rubber foot:脚垫
Bag:袋子
Washer:垫圈
Sleeve:袖套
Configuration:机构
Label hi-pot:高压标签
Firmware label:烧录标签
Metal cover:金属盖子
Plastic cover:塑胶盖子
Tape for packing:包装带
Bar code:条码
Tray:托盘
Collector :集线夹
Holder:固定器,L 铁
Connecter:连接器
IDE:集成电路设备,智能磁盘设备
SCSI:小型计算机系统接口
Gasket:导电泡棉
AGP:加速图形接口
PCI:周边组件扩展接口
LAN:局域网
USB:通用串形总线架构
Slim:小型化
COM:串型通讯端口
LPT:打印口,并行口
Power cord:电源线
I/O:输入,输出
Speaker:扬声器
EPE:泡棉
Carton:纸箱
Button:按键,按钮
Foot stand:脚架
版权声明:本文标题:验货缺陷英汉 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://www.elefans.com/xitong/1704479097a92898.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论