admin管理员组文章数量:1567919
2024年7月18日发(作者:)
PROGRAMMABLE CLUSTER HEADEND
FRPRO LIGHT HD
OPERATING INSTRUCTIONS
It is possible to download the FRPRO LIGHT HD manual on the relative product’s page on web site
PRODUCT DESCRIPTION
The Fracarro FRPRO LIGHT HD is an high selective programmable compact headend for filter, convert and amplify the
VHF/UHF Digital Terrestrial channels as well as mix the FM signal. The headend is a complete Digital Channel Processor
that can be used on small, medium or high installation plants as well as in hospitality environments.
Can process and convert more than 50 independent RF channels with very high selectivity on adjacent multiplexes
AGC automatic control circuit on all individual VHF and UHF input multiplexes
Isofrequency or converted channel filtering for every multiplex coming from VHF or UHF input.
Security code available for avoid incidental settings
1 FM input, 1 VHF+DAB input and 2 independent UHF inputs; with selectable 12-24 V remote power on VHF and UHF
inputs
PRODUCT INSTALLATION
Connect the device to the grounding electrode of the antenna system and fix the FRPRO LIGHT HD in vertical
position to guarantee the correct ventilation and heat dissipation.
Connect the power cord to the power supply socket and check the
STATUS
LED for DC power presence.
Connect FM, VHF and UHF aerial’s coaxial cables to the FRPRO LIGHT HD headend.
Connect the RF output coaxial cable to the RF coaxial distribution network.
If necessary, connect a field meter to the -30dB test port to check the quality signal.
Configure the device using the three settings buttons available on the top of the FRPRO LIGHT HD headend; press
the
confirm
button for two seconds to access to the main menu and use the
left/down
or
right/up
arrows to scroll
the sub-menu.
If necessary, the power adapter can easily be replaced, without unmount the product, by open the top left plastic cover;
please refer to the Safety Warnings chapter before proceed.
FACTORY SETUP: before starting the configuration, it is advised to set the correct VHF and UHF frequency plan.
Power off the device,
Push the
confirm
button and keep it pushing while you turn-on the FRPRO LIGHT HD.
Release the button when
RESET FINISHED
message is shown on display.
To activate the correct frequency plan select the
REGION
where the headend is situated and save with the
confirm
button; Europe (
EU
) is the default setting.
HEADEND CONFIGURATION
Press the
confirm
button for two seconds to access the different menus or for confirm the selection; scroll all the
menu by using
left/down
or
right/up
arrows for move through the different settings.
INPUT CONFIGURATION
Select
INPUT FM
to setup the desired FM input signal gain.
Select
INPUT VHF
,
INPUT UHF 1
o
INPUT UHF 2
to enter the VHF/UHF input settings.
Set
12V
or
24V
on
DC
if it is necessary to insert the power supply to feed the external must amplifiers; 100mA is the
total available current for VHF and UHF inputs; on advanced settings it is possible to set 12V or 24V.
Select
ADD CHANNEL
to add the RF channel on the list of the managed filtered multiplexers by the relative input; to
delete the unwanted RF channel, move on the position of the channel by using
left/down
or
right/up
arrows
buttons and press the
confirm
button for 3 seconds until
CHANNEL DELETED
message is shown on the display. Up
to 5 channels can be added and converted at once; first select the channels you want to add, then you can convert
them. For example:
o To add CH5 and convert to CH6, select as follows: 5: 5 -> 6: 6
o To add CH21-22-23 and convert to CH31-32-33, select as follows: 21:23 -> 31:33
For the best performances, it’s recommended to add and process only single channels, unless you need to process a lot
of channels.
2
OUTPUT CONFIGURATION
By selecting
OUTPUT
and
LEVEL
menu it is possible to define the total RF output level from 88dBµV to 108dBµV,
depending on the total multiplexes amount managed by the headend,
98dBµV
is the default level.
DC VOLTAGE:
set 12V or 24V remote power available on VHF and UHF inputs.
AUTO CH:
it suppresses noise when a channel stops broadcasting, to avoid the MER affect of neighbouring channels.
FILTER:
set the following filtering characteristics:
o
BEST MER
: best quality thanks to a larger filtering; it is not suitable for adjacent channel distribution.
o
OPTIMAL:
default value, best trade off between large filtering and high selectivity.
o
SHARP:
best selectivity tanks to a thinner filtering, suitable to distribute adjacent channels.
3
SAFETY WARNINGS
The product must only be installed by qualified persons, according to the local safety standards and regulations. Fracarro Radioindustrie is free
from all civil and criminal responsibilities due to breaches of the current legislation derived from the improper use of the product by the installer,
user or third parties. The product must be used in full compliance with the instructions given in this manual in order to protect the operator
against all possible injuries and the product from being damaged. Don’t open the product case: components under dangerous
voltage may be accessible when the case is opened.
Installation warnings
The product must not be exposed to any dripping or splashing and thus it should be installed indoors and in a dry location.
Handle the product carefully. Impacts can damage the product.
Excessive temperatures and/or an overheating may affect the performance and the life of the product.
In the event that the unit is fixed to the wall, use the proper screw anchors suitable to the characteristics of the fixing support. The wall and
the anchoring system must be able to support at least 4 times the weight of the unit.
Warning: to avoid injury, this appliance must be secured to the wall depending on the installation instructions. For "PERMANENTLY INSTALLED
APPLIANCES", an easily accessible cutting device must be added to the exterior of the appliance; for "APPLIANCES WITH A POWER PLUG", the
socket must be installed close to the appliance and easily accessible. The product must be connected to the grounding electrode of the antenna
system in compliance with standard EN 60728-11. The screw provided for this purpose is marked with the symbol:
It is recommended to comply with the provisions of the standard EN60728-11 and to connect this screw to the main earth node of the plant (do
not connect to intermediate points).
•
Earth screw symbol
Class II symbol
General warnings: In the event of a malfunctioning, do not try to fix the product as the guarantee would be invalidated. Only use the power
supply supplied with the product. Although the information given in this manual has been prepared carefully and thoughtfully, Fracarro
l. reserves the right to modify it without notice and to improve and/or modify the product described in this manual. See the
website to have information relevant to the technical support and product guarantee.
The recycling of materials will help to conserve natural resources.
CONFORMITY TO EUROPEAN LAWS
Fracarro declares that the product complies with EU Directive 2014/53 and 2011/65/UE. The full text of the EU Declaration of Conformity is
available on the following website .
USER’S INFORMATION
Disposal of Old Electrical & Electronic Equipment
Applicable in the European Union and other European countries with separate collection system
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Fracarro Radioindustrie SRL: Via Cazzaro n.3 - 31033 Castelfranco Veneto (TV) - ITALIA - Tel: +39 0423 7361 - Fax: +39 0423 736220
Fracarro France S.A.S.: 7/14 rue du Fossé Blanc Bâtiment C1 - 92622 Gennevilliers Cedex - FRANCE Tel: +33 1 47283400 - Fax: +33 1 47283421
Fracarro (UK) – Ltd: Suite F9A, Whiteleaf Business Centre, Little Balmer, Buckingham, MK18 1TF UK - Tel: +44(0)1908 571571 - Fax: +44(0)1908 571570
**************************************************@-chatwhatsapp+393357762667
4
F
R
P
R
O
L
I
G
H
T
H
D
-
E
0
2
-
1
2
-
2
0
1
9
-
r
e
v
.
0
3
Guaranteed by Fracarro Radioindustrie SRL Via Cazzaro n. 3, 31033 Castelfranco Veneto (Tv) – Italy
版权声明:本文标题:飞卡罗 FRPRO LIGHT HD 可编程集群前端操作说明说明书 内容由热心网友自发贡献,该文观点仅代表作者本人, 转载请联系作者并注明出处:https://www.elefans.com/dianzi/1721287218a869880.html, 本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容,一经查实,本站将立刻删除。
发表评论