RK3568调试HDMI

HDMI"/>

RK3568调试HDMI

一. 简介

• 本文是基于RK3568平台，HDMI-IN调试总结。

• 视频桥接芯片：双RK628D

• 驱动代码：“kernel\drivers\media\i2c\rk628”(驱动用的是rk628-for-all-v21版本)

• 本次调试的方案功能：HDMI-IN信号通过RK628D转换成MIPI-CSI传到主控SOC

• 参考文档：“RKDocs\common\RK628\Rockchip_RK628D_For_All_Porting_Guide_CN_V21.pdf”

• 场景描述：
  ① RK3568 不直接支持HDMI-IN接口，SOC有MIPI-CSI功能。需将HDMI-IN转换成MIPI-CSI才能获取视频信息。

  ②此文章使用场景是HDMI-IN通过龙讯switch芯片：LT8641UXE从四个HDMI-IN信号中通过上层应用选择一个HDMI-IN信号输出到RK628D芯片，RK628D再将HDMI-IN信号转换成MIPI-CSI信号输出到RK3588 SOC。通过软件抓取输入进SOC的视频信息。

③ 板上有8个HDMI-IN接口；两个龙讯LT8641UXE芯片；两个RK628D芯片。 因为四个HDMI-IN对应一个龙讯LT8641UXE芯片，对应一个RK628D芯片。

二. 视频桥接芯片RK628D调试

2.1 RK628驱动介绍

• RK628驱动有两个版本，一个是SDK系统自带的版本，一个是RK628-for-all版本。

• RK628 分为 Display 通路和 HDMI IN 通路，SDK 版本 Display 通路基于DRM框架，HDMI IN 通路基于V4L2框架。

• RK628-For-All 版本驱动一样也分为Display 通路和 HDMI IN 通路，Display 通路的驱动于drivers/misc/rk628/
  下，HDMI IN 通路的驱动于drivers/media/i2c/rk628/下。本文采用RK628-For-All 版本HDMI IN 通路：media

• Media 为 RK628 HDMI IN 通路的驱动代码，将RK628D作为类camera设备使用，实现如下功能。

2.2 调试总览，调试步骤分析

调试思路：先把四个HDMI-IN对应一个龙讯LT8641UXE芯片,对应一个RK628D芯片调好。再调另一组。

• 步骤 ① 移植驱动
• 步骤 ② dts编写
• 步骤 ③ 编译烧录

2.3 移植驱动：

① config配置：Rockchip_defconfig:

CONFIG_VIDEO_RK628=y (这是RK628-for-all media驱动开关配置)
CONFIG_DRM=y

2.4 dts编写

链接关系 1： sensor1->csi2_dphy1->mipi_csi2->rkcif_mipi_lvds ( vicap 链路 )

链接关系 2： sensor2->csi2_dphy2->rkisp_vir0 ( isp 链路 )

// 链接关系 1： sensor1->csi2_dphy1->mipi_csi2->rkcif_mipi_lvds,第一路index为0，facing配置为back
&i2c2 {//clock-frequency = <400000>;status = "okay";pinctrl-names = "default";pinctrl-0 = <&i2c2m1_xfer>;rk628_csi_v4l2: rk628_csi_v4l2@50 {status = "okay";reg = <0x50>;compatible = "rockchip,rk628-csi-v4l2";interrupt-parent = <&gpio0>;interrupts = <RK_PB0 IRQ_TYPE_LEVEL_HIGH>;enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;reset-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_LOW>;//hdcp-enable = <1>;scaler-en = <1>;assigned-clocks = <&pmucru CLK_WIFI>;assigned-clock-rates = <24000000>;clocks = <&pmucru CLK_WIFI>;clock-names = "soc_24M";plugin-det-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;rockchip,camera-module-index = <0>;rockchip,camera-module-facing = "back";rockchip,camera-module-name = "RK628-CSI";rockchip,camera-module-lens-name = "NC";port {hdmiin_out0: endpoint {remote-endpoint = <&hdmi_to_mipi_in>;data-lanes = <1 2>;};};};
};&csi2_dphy_hw {status = "okay";
};&csi2_dphy1 {status = "okay";ports {#address-cells = <1>;#size-cells = <0>;port@0 {reg = <0>;#address-cells = <1>;#size-cells = <0>;hdmi_to_mipi_in: endpoint@1 {reg = <1>;remote-endpoint = <&hdmiin_out0>;data-lanes = <1 2>;};};port@1 {reg = <1>;#address-cells = <1>;#size-cells = <0>;csidphy_out: endpoint@1 {reg = <1>;remote-endpoint = <&mipi_csi2_input>;data-lanes = <1 2>;};};};
};&mipi_csi2 {status = "okay";ports {#address-cells = <1>;#size-cells = <0>;port@0 {reg = <0>;#address-cells = <1>;#size-cells = <0>;mipi_csi2_input: endpoint@1 {reg = <1>;remote-endpoint = <&csidphy_out>;data-lanes = <1 2>;};};port@1 {reg = <1>;#address-cells = <1>;#size-cells = <0>;mipi_csi2_output: endpoint@0 {reg = <0>;remote-endpoint = <&cif_mipi_in>;data-lanes = <1 2>;};};};
};&rkcif {status = "okay";
};&rkcif_mipi_lvds {status = "okay";port {cif_mipi_in: endpoint {remote-endpoint = <&mipi_csi2_output>;data-lanes = <1 2>;};};
};&rkcif_mmu {status = "okay";
};//链接关系 2： sensor2->csi2_dphy2->rkisp_vir0,第二路index为1，facing配置为front&i2c2 {//clock-frequency = <400000>;status = "okay";pinctrl-names = "default";pinctrl-0 = <&i2c2m1_xfer>;rk628_csi_v4l2_1: rk628_csi_v4l2_1@51 {status = "okay";reg = <0x51>;compatible = "rockchip,rk628-csi-v4l2";interrupt-parent = <&gpio3>;interrupts = <RK_PC4 IRQ_TYPE_LEVEL_HIGH>;//enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>;reset-gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_LOW>;//hdcp-enable = <1>;scaler-en = <1>;assigned-clocks = <&pmucru CLK_WIFI>;assigned-clock-rates = <24000000>;clocks = <&pmucru CLK_WIFI>;clock-names = "soc_24M";plugin-det-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;rockchip,camera-module-index = <1>;rockchip,camera-module-facing = "front";rockchip,camera-module-name = "RK628-CSI";rockchip,camera-module-lens-name = "NC";port {hdmiin_out1: endpoint {remote-endpoint = <&mipi_in_ucam0>;data-lanes = <1 2>;};};};
};&csi2_dphy_hw {status = "okay";
};&csi2_dphy0 {status = "disabled";/delete-node/ ports;
};&csi2_dphy2 {status = "okay";ports {#address-cells = <1>;#size-cells = <0>;port@0 {reg = <0>;#address-cells = <1>;#size-cells = <0>;mipi_in_ucam0: endpoint@0 {reg = <0>;remote-endpoint = <&hdmiin_out1>;data-lanes = <1 2>;};};port@1 {reg = <1>;#address-cells = <1>;#size-cells = <0>;csidphy_out1: endpoint@0 {reg = <0>;remote-endpoint = <&isp0_in>;};};};
};&rkisp {status = "okay";
};&rkisp_mmu {status = "okay";
};&rkisp_vir0 {status = "okay";port {#address-cells = <1>;#size-cells = <0>;isp0_in: endpoint@0 {reg = <0>;remote-endpoint = <&csidphy_out1>;};};};

三. 调试命令：

• 查看media设备：

  ls /dev/media*
  

  /dev/media0  /dev/media1  
  

• i2c设备的通用调试命令：查看设备是否挂载到i2c总线下：

  i2cdetect -y 2
  

• 查看media节点的拓扑结构命令：

  media-ctl -d /dev/media0 -p
  media-ctl -d /dev/media1 -p
  media-ctl -p
  

• 抓图命令：

  v4l2-ctl  -d   /dev/video0  --set-fmt-video=width=1920,height=1080,pixelformat=NV12 --stream-mmap=3 --stream-skip=100 --stream-to=/oem/NV12.yuv --stream-count=1 --stream-poll