HCIP第二次实验"/>
HCIP第二次实验
配置ip
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip address 192.168.1.2 24
[r1-GigabitEthernet0/0/0]int s4/0/0
[r1-Serial4/0/0]ip address 12.1.1.1 24
[r2]int s3/0/0
[r2-Serial3/0/0]ip address 12.1.1.2 24
[r2-Serial3/0/0]int s3/0/1
[r2-Serial3/0/1]ip address 13.1.1.1 24
[r2-Serial3/0/1]int s4/0/0
[r2-Serial4/0/0]ip address 14.1.1.1 24
[r2]interface LoopBack 0
[r2-LoopBack0]ip address 2.2.2.2 24
[r3]int s4/0/0
[r3-Serial4/0/0]ip address 13.1.1.2 24
[r3-Serial4/0/0]int g0/0/0
[r3-GigabitEthernet0/0/0]ip address 192.168.2.2 24
[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]ip address 192.168.3.2 24
[r4-GigabitEthernet0/0/0]int s4/0/0
[r4-Serial4/0/0]ip address 14.1.1.2 24
R1和R2为 HDLC封装
[r1]int s4/0/0
[r1-Serial4/0/0]link-protocol hdlc
Warning: The encapsulation protocol of the link will be changed. Continue? [Y/N]:
Y
[r2]int s3/0/0
[r2-Serial3/0/0]link-protocol hdlc
Warning: The encapsulation protocol of the link will be changed. Continue? [Y/N]:
Y
R2到R3为PPP封装且PAP认证时R2为主认证方
[r2]aaa
[r2-aaa]local-user huawei password cipher 123456
[r2-aaa]local-user huawei service-type ppp
[r2]int s3/0/1
[r2-Serial3/0/1]link-protocol ppp
[r2-Serial3/0/1]ppp authentication-mode pap
[r3]int s4/0/0
[r3-Serial4/0/0]link-protocol ppp
[r3-Serial4/0/0]ppp pap local-user huawei password cipher 123456
R2到R4为PPP封装且CHAP认证时R2为主认证方
[r2]aaa
[r2-aaa]local-user huawei password cipher 123456
[r2-aaa]local-user huawei service-type ppp
[r2]int s4/0/0
[r2-Serial4/0/0]link-protocol ppp
[r2-Serial4/0/0]ppp authentication-mode chap
[r4]int s4/0/0
[r4-Serial4/0/0]link-protocol ppp
[r4-Serial4/0/0]ppp chap user huawei
[r4-Serial4/0/0]ppp chap password cipher 123456
做缺省,NET
[r1]ip route-static 0.0.0.0 0 12.1.1.2
[r1]acl 2000
[r1-acl-basic-2000]rule 1 permit source any
[r1]int s4/0/0
[r1-Serial4/0/0]nat outbound 2000
[r3]ip route-static 0.0.0.0 0 13.1.1.1
[r3]acl 2000
[r3-acl-basic-2000]rule 1 permit source any
[r3]int s4/0/0
[r3-Serial4/0/0]nat outbound 2000
[r4]ip route-static 0.0.0.0 0 14.1.1.1
[r4]acl 2000
[r4-acl-basic-2000]rule 1 permit source any
[r4]int s4/0/0
[r4-Serial4/0/0]nat outbound 2000
构建MGRE环境
将R1设置为中心站点
[r1]interface Tunnel 0/0/0
[r1-Tunnel0/0/0]ip address 10.1.1.1 24
[r1-Tunnel0/0/0]tunnel-protocol gre p2mp
[r1-Tunnel0/0/0]source 12.1.1.1
[r1-Tunnel0/0/0]nhrp entry multicast dynamic
[r1-Tunnel0/0/0]nhrp network-id 100
将 R3,R4设置为分支站点
[r3]interface Tunnel 0/0/0
[r3-Tunnel0/0/0]ip address 10.1.1.2 24
[r3-Tunnel0/0/0]tunnel-protocol gre p2mp
[r3-Tunnel0/0/0]source s4/0/0
[r3-Tunnel0/0/0]nhrp network-id 100
[r3-Tunnel0/0/0]nhrp entry 10.1.1.1 12.1.1.1 register
[r4]interface Tunnel 0/0/0
[r4-Tunnel0/0/0]ip address 10.1.1.3 24
[r4-Tunnel0/0/0]tunnel-protocol gre p2mp
[r4-Tunnel0/0/0]source s4/0/0
[r4-Tunnel0/0/0]nhrp network-id 100
[r4-Tunnel0/0/0]nhrp entry 10.1.1.1 12.1.1.1 register
设置 RIP
[r1]rip
[r1-rip-1]version 2
[r1-rip-1]network 10.0.0.0
[r1-rip-1]network 192.168.1.0
[r3]rip
[r3-rip-1]version 2
[r3-rip-1]network 10.0.0.0
[r3-rip-1]network 192.168.2.0
[r4]rip
[r4-rip-1]version 2
[r4-rip-1]network 10.0.0.0
[r4-rip-1]network 192.168.3.0
关闭R1上S4/0/0的水平分割
[r1]int Tunnel 0/0/0
[r1-Tunnel0/0/0]undo rip split-horizon
检测
PC1去PING PC2和PC3
PC2去PING PC3
PC1,PC2,PC3访问R2的环回
更多推荐
HCIP第二次实验
发布评论