Telerik + Visual Studio 2010工具箱=令人困扰的问题

本文介绍了Telerik + Visual Studio 2010工具箱=令人困扰的问题的处理方法，对大家解决问题具有一定的参考价值，需要的朋友们下面随着小编来一起学习吧！ 问题描述

有没有人找到以下任一问题的解决方案:

在Visual Studio 2010中进入任何设计模式(WPF，EDMX，Silverlight，Reporting等)时，我在状态栏中看到一条消息，例如Loading toolbox content from package Microsoft.VisualStudio.IDE.Toolbox.ControlInstaller.ToolboxInstallerPackage '{2C98B35-07DA-45F1-96A3-BE55D91C8D7A}'...，这每次都会锁定VS一分钟.

Telerik工具箱有很多重复的控件.

工具箱在展开时不显示任何项目.我认为这是因为其中包含太多控件.

我相信所有这些问题都是相关的.我认为，发生#1时，重复的控件会添加到某些工具箱中，最终导致#3发生.

我对此感到厌烦，并且我很确定这是由Telerik的"Rad"东西引起的.我有2台开发机，直到安装了一些rad控件，它们才做任何这样的事情.

解决方案

看看我在Telerik网站上发布的这篇文章(9月7日，底部附近)

简而言之，可能是导致Toolbox缓存初始化过程崩溃的其他原因(在我的情况下，这是WCF RIA Services Toolkit，2011年4月).一旦我摆脱了那一切，一切就恢复了顺风顺水.我很幸运，因为我只安装了RIA工具包进行测试，因此我可以删除它而不影响我的工作流程.不确定是否需要RIA工具包该怎么做...

无论如何，值得一看！

哦，我完全同意，这个问题很糟糕.我到了每天要等待5分钟才能准备好IDE的地步……在过去的几个月中，这浪费了很多时间！

Has anyone ever found a solution to either of these problems:

When entering any design mode in Visual Studio 2010 (WPF, EDMX, Silverlight, Reporting, etc) I see a message in the status bar like Loading toolbox content from package Microsoft.VisualStudio.IDE.Toolbox.ControlInstaller.ToolboxInstallerPackage '{2C98B35-07DA-45F1-96A3-BE55D91C8D7A}'... This locks VS for about a minute everytime.

Telerik toolboxes have many duplicate controls.

Toolbox doesn't show any items when expanded. I think this is because it has too many controls in it.

I believe all of these issues to be related. I think when #1 happens, duplicate controls are added to some toolboxes, which eventually causes #3 to happen.

I'm sick of this and I'm pretty sure it's caused by Telerik's "Rad" stuff. I have 2 dev machines that never did any of this until I installed some rad controls.

解决方案

Take a look at this post I made on the Telerik website (post on Sep 7th near the bottom)

In a nutshell, it may be something else that is crashing the Toolbox cache initialisation process (in my case it was WCF RIA Services Toolkit April 2011). Once I got rid of that it was all back to smooth sailing. I was lucky in that I only had the RIA toolkit installed for testing so I could remove it without impacting my workflow. Not sure what you'd do if you needed the RIA toolkit though...

Anyway, it's worth looking in to!

Oh, and I agree entirely that the issue sucks big-time. I was getting to the point where I had to wait 5 minutes each day for the IDE to get ready...that's a lot of hours of wasted time over the past few months!